Archive for June, 2011


Received on 05May11, 6.00am
Hi Deacken,

I’ve seen your site, nice work!
Can you please show me a scheme about the driver circuit for the vortex coil?
I’ve built a 12vdc inverter that produces 170vac; it’s a 555 timer circuit that drives a step-up transformer.
I’ve tested it with a vortex coil that I’ve built following your video on youtube, but it doesn’t seem to work, no force is generated.
Where am I wrong?
May it be good for this purpose?
I’ve been searching for years without results about electro-gravity and electrets, now I see an open window with your words, please help me!
Thanks for your time

Francesco (from Italy)

Replied on 05May11 3.00pm
Hi there Francesco,

At first, I read some books that shifted my belief that UFO is not from alien origin at all!

Next stage was to explore from my physics point of view how possible to build my personal UFO with my background in Pure Physics Degree. Only one answer was coming to my mind during all these years…MHD (Magneto Hydro Dynamic)

Then, in 2007 I did read about Victor Grebennikov of his flying plate from Russia. After explore most of you tuber believe of his flying plate using only chitin and not required any electric (which is delivered by video of Jerry Decker), it took me 2 years to experiment with Cavernous Structure Effect (CSE) and any possible geometric shape that produce CSE. Just plain stupid!

Then in November 2008, I did visualized of Vortex Magnetic Field produced by vortex coil (like the one that I published up inside you tube in my name) and by “combining” Magnetic and Electric field together (Lorentz force), I did produce MHD in small scale.

Good things that you did complete the vortex coil, but the vortex coil only produces Magnetic Field in center hole Vortex direction. AC only make the Vortex direction goes from right to left and up and down direction….remember you only produce AC Vortex Magnetic Field with my vortex coil.

The next part that you missing was the High Voltage Electric Field which consist of 2 aluminum plate which will cover up your Vortex coil.

To step up the voltage to high voltage, I’m using small spark plug coil from Yamaha motorcycle.

The connection from battery to 12VDC inverter (only positive AC wire) to vortex coil to step up spark plug coil to aluminum plate. Then, on natural wire from 12VDC inverter will be terminate back to negative of the battery.

Remember to visualized the Magnetic and Electric Field on top of each aluminum plate surface because only the combining force field will produce the MHD anti-gravity effect.

Additional notes: when commissioning, please put the aluminum surface with wooden stand (2 inch in height) because High Voltage spark might jump from aluminum surface to the table and discharge the overall electric field which been produce just above the aluminum surface.

Finally, my complete commissioning of this item (small prototype of UFO) was done around February 2009 with success.

I will follow up my step by step video how to build this small prototype for you to make it as a weekend project.

And my hope was…. there will be full scale of flying vehicle in the near future using my only published video.

Hope this will explain your curiosity.

Thanks

Regards,
Deacken Frost

Advertisements

Melbourne time 4.21pm 25Jun11,

I’m sorry if I’m too slow to published this secret because I have to explain by drawing each and every picture and the highlight by my previous experiments in Bintulu on year 2009 …
For the first time I be able reveal the secret of run a Produa Kancil EX850 Auto by only water…
Up until now I didn’t have the opportunity to replicate this project because lack of equipment, time and parts.

I’m intending to publish this thing based on the following basis:
a) My cousin Firdaus has the necessary equipment to install these things.
b) My other cousin Zahrul have the necessary skills to manufacturing the parts and export to my cousin Firdaus for further assemble and installation.
c) Further advertising can be made by Zahrul’s brother Badin in private or with the help of his current company he work now called “Green Base Technology”.

Now I’m waiting an excellent opportunity to launch the thing all over Malaysia, I think now it’s time to share knowledge which I acquired in Bintulu first time ….

This is because:
a) Firdaus now not have any permanent jobs and he’s now having a new born daughter…it’s not too late to secure some financial for his family….
b) We can change our children’s future (the next generation) by showing them that they do not have to depend on the fossil fuel to run their future vehicle ….
c) The changing of technology now make me realized that it would be more easy to build this things compare to 5 years ago …
d) I’d notice that by doing this things alone, I wouldn’t achieve anything… so we have to built a team to create this idea to become reality….


Information for above figure as follows:
a) If we have pure hydrogen gas, and we put a pipe into the “air intake” of an engine…
b) If the engine is in idling mode… we can increase the engine RPM by feeding more hydrogen gas into it ….
c) This means that we can use only hydrogen to run our cars.

Information for the Youtube above as follows:
a) It’s been taken from the youtube movies posted in “Mythbuster”
b) To show you that we can use just enough hydrogen to turn on the engine.
c) Mythbuster in this episode trying to prove whether the electrolysis of water is able to run a car or just enough to turn the engine on …
d) In these episodes, Mythbuster have proven that electrolysis FAILED start the engine using water electrolysis because the hydrogen production is too slow.
e) BUT successfully demonstrated that the engine can be turned on if only hydrogen gas being put into the engine air intake.


Explanation for above figure as follows:
a) The original figure were taken from form 5 Malaysian high school chemistry book… but it has been modified by me for easy to understand …
b) The experiment explaining of a Redox Experiment … or oxidation of iron into iron magnetite.
c) Its chemical formula is as follows:

3Fe + 4H2O -> Fe3O4 + 4H2
Where;
Fe = Iron (Iron)
H2O = Ayor (Water)
Fe3O4 = Iron Magnetite
H2 = Hydrogen Gas

d) But these formula have two conditions which is… the water must be in the form of vapor or steam…the iron must reach 240 degrees Celsius of heat … in other words, the iron must be red hot….
e) As the “Water Steam / Vapor Generator” produces water in the form of vapor or steam …and the “Hydrogen generator converter” then heat up the steel ball bearings to red hot
f) The combination of these two things to produce hydrogen gas easily and abundantly….
g) Now we must think on how to simplify these parts and simplify installation to our cars or just any car in the world….


Information for above figure as follows:
a) These setup shows on how do I manage to install my Produa EX850 car in Bintulu…
b) First, normal copper pipe will be stuffed by iron nails which will be cut on the top and bottom of the nails .. Leave only the middle part of the iron nails…. this copper pipes will be seal air tight…with a connector on each ends…
c) Then make a hole on the car exhaust pipe and installed the copper pipe containing nails across the exhaust…
d) This will make the exhaust heat to heat up the nails inside the copper tube….when copper pipe in the middle of the exhaust pipe the fume inside the exhaust become more tight and it will reduces engine performance a little … the heat produce into the copper tube with nails inside depending on how the fumes inside the exhaust being compressed…. but …when hot air from the exhaust fumes compressed into narrow place … then the higher the heat ….. The more heat generate the batter this devices performed….
e) Under the copper tube which been filled with nails is a copper pipe cut in half to catch the high pressure fumes to high pressure canister ….
f) Valve will be controlled by a cable to the second gas pedal…. the second gas pedal is placed next to the cars original gas pedal… the operation of the second gas pedal is when we placed our foot to the pedal, the valves will be opened…and when we lift our foot from the pedal … valve will be closed…
g) High-pressure containers filled just any type of water and will be tightly closed…
h) The water vapor will come out from the canister…contact with the red hot iron….. And turn the water into hydrogen according to the formula given previously….
i) And the hydrogen will be fed into the car’s air intake…..

My previous design needs to set the nail into red hot manually….so, I drive the car with normal petrol by using the original gas pedal….this heating up operations acquired by driving the car with original gas pedal for 15 to 20 minutes… when iron nail inside the copper pipe is hot enough (I was using thermostat indicator to check the temperature reaching 300 degree centigrade)… then I pressed the second gas pedal to open the valve… and for the resulting hydrogen gas will run the car….

Usually when we use the second pedal, the engine originally in idling mode (timing) so that the second pedal inject the hydrogen into the engine air intake to increased RPM and run the car….very little fossil fuel still needed for car’s timing….

During my time in Bintulu in 2009 … I did some test with just any water including coke water, water from puddles, seawater, rain water, drain water, and urine……but urine will create a very bad smell when you wanted to filled up new water inside the pressure containers…..and at one time I did manage test by mixing the various type of water. Examples the sea water plus rain water plus coke water…the engine still running smoothly….

If the car can sprint top speed of 140km/h originally….because of the copper pipe barriers inside the car exhaust….at vehicle speeds would be less top speed of 140km/h…

I still need some comments or ideas on how to make this part easy and cheaper to make..And the idea for easy installations without any hassle…..

Hopefully it can be producing mass in productions and the installation will be “plug and play” method….

Thank you for reading and waiting for your comment….